deleting simple SPS from master

SimpleSPS/SImpleSPS/SImpleSPS.ino

@@ -1,518 +0,0 @@
-/*
-  Simple SPS System mit dem Arduino.
-*/
-
-// defining different hardware platforms
-#ifdef __AVR_ATmega328P__
-//#define SPS_USE_DISPLAY
-//#define SPS_RECEIVER
-//#define SPS_ENHANCEMENT
-//#define SPS_SERIAL_PRG
-//#define SPS_SERVO
-//#define SPS_TONE
-#endif
-
-// libraries
-#include <makros.h>
-#include <EEPROM.h>
-#include <avr/eeprom.h>
-
-#include "hardware.h"
-
-// Commands
-const byte PORT = 0x10;
-const byte DELAY = 0x20;
-const byte JUMP_BACK = 0x30;
-const byte SET_A = 0x40;
-const byte IS_A = 0x50;
-const byte A_IS = 0x60;
-const byte CALC = 0x70;
-const byte PAGE = 0x80;
-const byte JUMP = 0x90;
-const byte C_COUNT = 0xA0;
-const byte D_COUNT = 0xB0;
-const byte SKIP_IF = 0xC0;
-const byte CALL = 0xD0;
-const byte CALL_SUB = 0xE0;
-const byte CMD_BYTE = 0xF0;
-
-// debouncing with 100ms
-const byte DEBOUNCE = 100;
-
-// sub routines
-const byte subCnt = 7;
-word subs[subCnt];
-
-// the actual address of the program
-word addr;
-// page register
-word page;
-// defining register
-byte a, b, c, d;
-
-const byte SAVE_CNT = 1;
-
-word saveaddr[SAVE_CNT];
-byte saveCnt;
-
-unsigned long tmpValue;
-
-byte prog = 0;
-byte data = 0;
-byte com = 0;
-
-void setup() {
-  pinMode(Dout_0, OUTPUT);
-  pinMode(Dout_1, OUTPUT);
-  pinMode(Dout_2, OUTPUT);
-  pinMode(Dout_3, OUTPUT);
-
-  pinMode(PWM_1, OUTPUT);
-  pinMode(PWM_2, OUTPUT);
-
-  pinMode(Din_0, INPUT_PULLUP);
-  pinMode(Din_1, INPUT_PULLUP);
-  pinMode(Din_2, INPUT_PULLUP);
-  pinMode(Din_3, INPUT_PULLUP);
-
-  pinMode(SW_PRG, INPUT_PULLUP);
-  pinMode(SW_SEL, INPUT_PULLUP);
-
-  digitalWrite(Dout_0, 1);
-  delay(1000);
-  digitalWrite(Dout_0, 0);
-
-  prgDemoPrg();
-  doReset();
-
-  if (digitalRead(SW_PRG) == 0) {
-    programMode();
-  }
-}
-
-void doReset() {
-
-  for (int i = 0; i < subCnt; i++) {
-    subs[i] = 0;
-  }
-
-  readProgram();
-
-  addr = 0;
-  page = 0;
-  saveCnt = 0;
-  a = 0;
-  b = 0;
-  c = 0;
-  d = 0;
-}
-
-/*
-  getting all addresses of sub programms
-*/
-void readProgram() {
-  word addr = 0;
-  for ( addr = 0; addr <= E2END; addr++) {
-    byte value = EEPROM.read(addr);
-
-    if (value == 0xFF) {
-      // ende des Programms
-      break;
-    }
-    byte cmd = (value & 0xF0);
-    byte data = (value & 0x0F);
-
-    if (cmd == CALL_SUB) {
-      if (data >= 8) {
-        data = data - 8;
-        subs[data] = addr + 1;
-      }
-    }
-  }
-}
-
-/*
-  main loop
-*/
-void loop() {
-  byte value = EEPROM.read(addr);
-  byte cmd = (value & 0xF0);
-  byte data = (value & 0x0F);
-
-  addr = addr + 1;
-  switch (cmd) {
-    case PORT:
-      doPort(data);
-      break;
-    case DELAY:
-      doDelay(data);
-      break;
-    case JUMP_BACK:
-      doJumpBack(data);
-      break;
-    case SET_A:
-      doSetA(data);
-      break;
-    case A_IS:
-      doAIs(data);
-      break;
-    case IS_A:
-      doIsA(data);
-      break;
-    case CALC:
-      doCalc(data);
-      break;
-    case PAGE:
-      doPage(data);
-      break;
-    case JUMP:
-      doJump(data);
-      break;
-    case C_COUNT:
-      doCCount(data);
-      break;
-    case D_COUNT:
-      doDCount(data);
-      break;
-    case SKIP_IF:
-      doSkipIf(data);
-      break;
-    case CALL:
-      doCall(data);
-      break;
-    case CALL_SUB:
-      doCallSub(data);
-      break;
-    default:
-      ;
-  }
-  if (addr > E2END) {
-    doReset();
-  }
-}
-
-/*
-  output to port
-*/
-void doPort(byte data) {
-  digitalWrite(Dout_0, (data & 0x01) > 0);
-  digitalWrite(Dout_1, (data & 0x02) > 0);
-  digitalWrite(Dout_2, (data & 0x04) > 0);
-  digitalWrite(Dout_3, (data & 0x08) > 0);
-}
-
-/*
-  delay in ms
-*/
-void doDelay(byte data) {
-  switch (data) {
-    case 0:
-      delay(1);
-      break;
-    case 1:
-      delay(2);
-      break;
-    case 2:
-      delay(5);
-      break;
-    case 3:
-      delay(10);
-      break;
-    case 4:
-      delay(20);
-      break;
-    case 5:
-      delay(50);
-      break;
-    case 6:
-      delay(100);
-      break;
-    case 7:
-      delay(200);
-      break;
-    case 8:
-      delay(500);
-      break;
-    case 9:
-      delay(1000);
-      break;
-    case 10:
-      delay(2000);
-      break;
-    case 11:
-      delay(5000);
-      break;
-    case 12:
-      delay(10000);
-      break;
-    case 13:
-      delay(20000);
-      break;
-    case 14:
-      delay(30000);
-      break;
-    case 15:
-      delay(60000);
-      break;
-    default:
-      break;
-  }
-}
-
-/*
-  jump relative back
-*/
-void doJumpBack(byte data) {
-  addr = addr - data - 1;
-}
-
-/*
-  a = data
-*/
-void doSetA(byte data) {
-  a = data;
-}
-
-/*
-  a = somthing;
-*/
-void doAIs(byte data) {
-  switch (data) {
-    case 1:
-      a = b;
-      break;
-    case 2:
-      a = c;
-      break;
-    case 3:
-      a = d;
-      break;
-    case 4:
-      a = digitalRead(Din_0) + (digitalRead(Din_1) << 1) + (digitalRead(Din_2) << 2) + (digitalRead(Din_3) << 3);
-      break;
-    case 5:
-      a = digitalRead(Din_0);
-      break;
-    case 6:
-      a = digitalRead(Din_1);
-      break;
-    case 7:
-      a = digitalRead(Din_2);
-      break;
-    case 8:
-      a = digitalRead(Din_3);
-      break;
-    case 9:
-      tmpValue = analogRead(ADC_0);
-      a = tmpValue / 64; //(Umrechnen auf 4 bit)
-      break;
-    case 10:
-      tmpValue = analogRead(ADC_1);
-      a = tmpValue / 64; //(Umrechnen auf 4 bit)
-      break;
-    default:
-      break;
-  }
-}
-
-/*
-  somthing = a;
-*/
-void doIsA(byte data) {
-  switch (data) {
-    case 1:
-      b = a;
-      break;
-    case 2:
-      c = a;
-      break;
-    case 3:
-      d = a;
-      break;
-    case 4:
-      doPort(a);
-      break;
-    case 5:
-      digitalWrite(Dout_0, (a & 0x01) > 0);
-      break;
-    case 6:
-      digitalWrite(Dout_1, (a & 0x01) > 0);
-      break;
-    case 7:
-      digitalWrite(Dout_2, (a & 0x01) > 0);
-      break;
-    case 8:
-      digitalWrite(Dout_3, (a & 0x01) > 0);
-      break;
-    case 9:
-      tmpValue = a * 16;
-      analogWrite(PWM_1, tmpValue);
-      break;
-    case 10:
-      tmpValue = a * 16;
-      analogWrite(PWM_2, tmpValue);
-      break;
-    default:
-      break;
-  }
-}
-
-/*
-  calculations
-*/
-void doCalc(byte data) {
-  switch (data) {
-    case 1:
-      a = a + 1;
-      break;
-    case 2:
-      a = a - 1;
-      break;
-    case 3:
-      a = a + b;
-      break;
-    case 4:
-      a = a - b;
-      break;
-    case 5:
-      a = a * b;
-      break;
-    case 6:
-      a = a / b;
-      break;
-    case 7:
-      a = a & b;
-      break;
-    case 8:
-      a = a | b;
-      break;
-    case 9:
-      a = a ^ b;
-      break;
-    case 10:
-      a = ~a;
-      break;
-    default:
-      break;
-  }
-  a = a & 15;
-}
-
-/*
-  setting page
-*/
-void doPage(byte data) {
-  page = data * 16;
-}
-
-/*
-  jump absolute
-*/
-void doJump(byte data) {
-  addr = page + data;
-}
-
-/*
-  counting with c register
-*/
-void doCCount(byte data) {
-  if (c > 0) {
-    c -= 1;
-    c = c & 0x0F;
-    doJump(data);
-  }
-}
-
-/*
-  counting with d register
-*/
-void doDCount(byte data) {
-  if (d > 0) {
-    d -= 1;
-    d = d & 0x0F;
-    doJump(data);
-  }
-}
-
-/*
-  simple condition = true, skip next command
-*/
-void doSkipIf(byte data) {
-  bool skip = false;
-  switch (data) {
-    case 1:
-      skip = (a > b);
-      break;
-    case 2:
-      skip = (a < b);
-      break;
-    case 3:
-      skip = (a == b);
-      break;
-    case 4:
-      skip = digitalRead(Din_0);
-      break;
-    case 5:
-      skip = digitalRead(Din_1);
-      break;
-    case 6:
-      skip = digitalRead(Din_2);
-      break;
-    case 7:
-      skip = digitalRead(Din_3);
-      break;
-    case 8:
-      skip = !digitalRead(Din_0);
-      break;
-    case 9:
-      skip = !digitalRead(Din_1);
-      break;
-    case 10:
-      skip = !digitalRead(Din_2);
-      break;
-    case 11:
-      skip = !digitalRead(Din_3);
-      break;
-    case 12:
-      skip = !digitalRead(SW_PRG);
-      break;
-    case 13:
-      skip = !digitalRead(SW_SEL);
-      break;
-    case 14:
-      skip = digitalRead(SW_PRG);
-      break;
-    case 15:
-      skip = digitalRead(SW_SEL);
-      break;
-    default:
-      break;
-  }
-  if (skip) {
-    addr += 1;
-  }
-}
-
-/*
-  calling a subroutine
-*/
-void doCall(byte data) {
-  saveaddr[saveCnt] = addr;
-  saveCnt++;
-  addr = page + data;
-}
-
-/*
-  calling a subroutine, calling return and restart
-*/
-void doCallSub(byte data) {
-  if (data == 0) {
-    if (saveCnt < 0) {
-      doReset();
-      return;
-    }
-    saveCnt -= 1;
-    addr = saveaddr[saveCnt];
-    return;
-  }
-}

SimpleSPS/SImpleSPS/hardware.h

@@ -1,20 +0,0 @@
-// defining the hardware connections
-
-// Arduino Hardware
-const byte Din_0 = 0;
-const byte Din_1 = 1;
-const byte Din_2 = 2;
-const byte Din_3 = 3;
-
-const byte Dout_0 = 4;
-const byte Dout_1 = 5;
-const byte Dout_2 = 6;
-const byte Dout_3 = 7;
-
-const byte ADC_0 = 0; //(15)
-const byte ADC_1 = 1; //(16)
-const byte PWM_1 = 9;
-const byte PWM_2 = 10;
-
-const byte SW_PRG = 8;
-const byte SW_SEL = 11;

SimpleSPS/SImpleSPS/prgmode.ino

@@ -1,144 +0,0 @@
-/*
-  entering the programming mode
-*/
-
-#define BLINK_DELAY 500
-#define SHOW_DELAY 1000
-#define KEY_DELAY 250
-#define ADDR_LOOP 50
-
-const byte demoPrg[] = { 0x4F, 0x59, 0x1F, 0x29, 0x10, 0x29, 0x5A, 0x40,
-                         0x59, 0x64, 0x54, 0x29, 0x4F, 0x59, 0x10, 0xCD,
-                         0x11, 0x28, 0xCC, 0x18, 0x28, 0x4F, 0x59, 0x5A,
-                         0x72, 0x26, 0xC0, 0x35, 0x80, 0x90, 0xFF
-                       };
-
-
-enum PROGRAMMING_MODE {ADDRESS, COMMAND, DATA};
-
-PROGRAMMING_MODE prgMode;
-
-void prgDemoPrg() {
-  byte value = EEPROM.read(0);
-  if (value == 0xFF) {
-    value = EEPROM.read(1);
-    if (value == 0xFF) {
-      for (byte i = 0; i < sizeof(demoPrg); i++) {
-        EEPROM.write(i, demoPrg[i]);
-      }
-    }
-  }
-}
-
-void programMode() {
-  // checking if advance programmer board connected?
-  doPort(0x08);
-  while (digitalRead(SW_PRG) == 0) {
-    // waiting for PRG to release
-  }
-  blinkAll();
-  prgMode = ADDRESS;
-  addr = 0;
-  do {
-    blinkD1();
-    // LoNibble Adresse anzeigen
-    doAddr(addr);
-    //delay(SHOW_DELAY);
-
-    blinkD2();
-    // HiNibble Adresse anzeigen
-    data = (addr & 0xf0) >> 4;                                  //Adresse anzeigen
-    doAddr(data);
-    //delay(SHOW_DELAY);
-
-    byte Eebyte = EEPROM.read(addr);
-    data = Eebyte & 15;
-    com = Eebyte >> 4;
-
-    blinkD3();
-    prgMode = COMMAND;
-    doPort(com); //show command
-
-    do {
-      if (digitalRead(SW_SEL) == 0) {
-        delay(KEY_DELAY);
-        com += 1;
-        com = com & 0x0F;
-        doPort(com);
-      }
-    }
-    while (digitalRead(SW_PRG) == 1);
-    delay(DEBOUNCE);
-
-    blinkD4();
-    prgMode = DATA;
-    doPort(data); //show data
-
-    do {
-      if (digitalRead(SW_SEL) == 0) {
-        delay(KEY_DELAY);
-        data += 1;
-        data = data & 0x0F;
-        doPort(data);
-      }
-    }
-    while (digitalRead(SW_PRG) == 1); // S2 = 1
-    delay(DEBOUNCE);
-
-    byte newValue = (com << 4) + data;
-    if (newValue != Eebyte) {
-      EEPROM.write(addr, newValue); //           Writeeeprom Eebyte , Addr
-      blinkAll();
-    }
-    addr += 1;
-  }
-  while (true);
-}
-
-void blinkAll() {
-  blinkNull();
-  doPort(0x0F);
-  delay(BLINK_DELAY);
-}
-
-void blinkD1() {
-  blinkNull();
-  doPort(0x01);
-  delay(BLINK_DELAY);
-  blinkNull();
-}
-
-void blinkD2() {
-  blinkNull();
-  doPort(0x02);
-  delay(BLINK_DELAY);
-  blinkNull();
-}
-
-void blinkD3() {
-  blinkNull();
-  doPort(0x04);
-  delay(BLINK_DELAY);
-  blinkNull();
-}
-
-void blinkD4() {
-  blinkNull();
-  doPort(0x08);
-  delay(BLINK_DELAY);
-  blinkNull();
-}
-
-void blinkNull() {
-  doPort(0x00);
-  delay(BLINK_DELAY);
-}
-
-void doAddr(byte value) {
-  for (byte i = ADDR_LOOP; i > 0; i--) {
-    doPort(value);
-    delay(19);
-    doPort(0x0F);
-    delay(1);
-  }
-}